Handley Page H.P.115

1961

Back to the Virtual Aircraft Museum
  RESEARCH AIRCRAFTVirtual Aircraft Museum / United Kingdom / Handley Page  

Handley Page H.P.115

Test aircraft designed to test the behaviour of the delta wing at low speeds. The first flight was on August 17, 1961.

Handley Page H.P.115

Specification 
 MODELH.P.115
 CREW1
 ENGINE1 x Bristol Siddeley "Viper 9" turbojet, 860kg
 WEIGHTS
  Take-off weight2290 kg5049 lb
 DIMENSIONS
  Wingspan6.1 m20 ft 0 in
  Length13.7 m45 ft 11 in
  Wing area40.0 m2430.56 sq ft
 PERFORMANCE
  Max. speed400 km/h249 mph
  Range500 km311 miles

Comments
Ernest Smith, e-mail, 07.12.2016 13:48

I worked in the main drawing office when HP 115 was being designed and was involved with the design of the engine controls. I was also involved with the flying control system on Victor B Mark 2. HP 115 was built to test the low speed flying characteristics of the delta wing that was to be used for Concord. It is true that Neil Armstrong flew HP 115 at Bedford and I have photographs of him in the cockpit. The late 50s and the early 60s were a magic time to be working in the aircraft industry. I went through their drawing school, where George Bootle taught me all the 3 dimensional geometry that I shall ever need. I later designed for Westand Helicopters & the lectured in engineering. E.S.

reply

terry joyce, e-mail, 09.05.2024 Ernest Smith

Hello,
I just found this and hope that you receive this. Do you remember Philip Salt?

Best wishes
Terry Joyce

reply

John Parker, e-mail, 05.04.2015 15:10

ParkerIts amazing to me that some of the commentst above my Jan '09 comment are not right. The detail design was under George King in the Main Cricklewood DO and I got involved as I had done wooden glider repair work at Radlett. The only wing leading edge section used was symmetrical and I do not remember a weights section in the old Rolls Royce workshop that housed the DO.I suspect that the chap from Hunting got confused with their 126 low speed research which I think I last saw at Cosford, and was a bit later than the HP 115.

reply

john wilson, e-mail, 27.02.2013 23:32

Don't know why it is surprising that its beside the Concorde at FAAM as it was designed by Hunting Aircraft at their design office in Cavendish Sq, London, with the intention that HP build it as a test ac to examine slow speed characteristics of Concorde wing.I was a junior weights engineer with HA

reply

Barry, 13.09.2012 14:06

Ann Bolton, you are quite right the HP115 was used in connection with the Concorde programme.

reply

Ann Bolton, e-mail, 01.05.2012 13:48

I always understood that the HP115 was a test bed for various wing leading edge shapes as part of the development of Concorde. As a Weight engineer, I was responsible for all the calculations of the wooden sections. I don't remember how many there were but new designs kept landing on my desk. You can imagine the pride I felt when I was Condorde make its maiden flight.

reply

Sven, 20.11.2011 20:52

An enquiry to the Handley Page Society would be a good place for information about the firms staff.Don't have an address but google should get it.

reply

Shannyn, e-mail, 16.11.2011 18:02

@ Parker
Phillip,
My Great Grandmother worked there, her name was Daisy Julie Munday, and she was a tracer for both HP and de Havilland, can you tell us more about owrking in the design deoartment?

reply

JL Tait, e-mail, 08.07.2011 05:24

I read that Neil Armstrong once flew this plane.Is this true?

reply

toni, e-mail, 22.01.2011 23:48

My Grandfather Henry Barker worked there as a pannel beater, Great grand father George Cowie worked there as a sand Blaster my great uncle was a shop steward, my mother in the office as a typist. I was born and raised in Cricklewood Lane and taken to airshows as a child. Handley Pages has a long attachment to my family

reply

karl haston., e-mail, 06.11.2009 21:59

In 1953, I joined Handley Pages as an apprentice fitter working on Hastings,Canberras,Victors, & other projects at cricklewood & radlett factories. Before I left 1961, I was working on jigging for the HP115 which was supposed to be a glider to test low speed landings etc, Because of goverment cut backs of work @ HPs I decided to leave for work else where. I was amazed to hear that the craft is now located @ the fleetair arm museum . Why there ?.

reply

karl haston., e-mail, 06.11.2009 21:59

In 1953, I joined Handley Pages as an apprentice fitter working on Hastings,Canberras,Victors, & other projects at cricklewood & radlett factories. Before I left 1961, I was working on jigging for the HP115 which was supposed to be a glider to test low speed landings etc, Because of goverment cut backs of work @ HPs I decided to leave for work else where. I was amazed to hear that the craft is now located @ the fleetair arm museum . Why there ?.

reply

paul scott, e-mail, 20.08.2009 15:56

An amazing story, Phillip, thanks for sharing it with us - I'll never look at Cricklewood as dour and boring again after that! (Which unfortunately, it is!)

reply

Parker, e-mail, 05.01.2009 22:09

I was one of the design team (probably the last survivor as all of the others were older) and had the job of sorting snags during the build at Cricklewood as well as drawing various sections of the structure. Did it not have a Viper 11 for some of the early testing that was borrowed from Huntings Jet Provost 3? The nosegear was from a Jet Provost 3 and the main gear from a Piston Provost. If you look in the cockpit the parking brake lever came from the local Ford dealers for an Anglia car(I went out and bought it) At nose, tail and wingtips there were some detachable steel weights for test, which came from the jig scrapyard and were made into aircraft material under duress from the AID!!

reply

Do you have any comments?

Name    E-mail


COMPANY
PROFILE


All the World's Rotorcraft


All rhe World's Rotorcraft AVIATION TOP 100 - www.avitop.com Avitop.com